020-84858360
020-84858360
Many people feel overwhelmed by the installation of garage door sealers. In fact, there are 6 common types of garage doors, which are sectional, roll-up, side-sliding, side-hinged, and upward-sloping canopy. and retractable garage doors that tilt upward. We must understand these garage door workflows or how they work in order to have a good understanding of where the garage door seal brushes are installed. The sectional garage door is the most popular type of sectional garage door in the United States, and it is made up of multi-fast panels. The panels are in close contact, so there will be no gaps between the panels. It is generally recommended to install a sectional top of the garage door, door side seals, and door bottom. Determine the length of the sealing brush according to the length and width of your own garage. Generally, you need 5 to 6 garage door sealing brush strips, which can not only ensure the beautiful appearance of the garage but also protect the car from being covered by ash. Rolling shutter doors are mostly used in commercial garage doors and are generally seen in repair garages. This kind of door saves the position of the ceiling. Like its name, the working mode of the rolling shutter door is to roll up the iron sheet and hang it on the top of the door. Therefore, the rolling door is also installed with a sealing brush on the top, and on both sides and bottom of the door. The sealing brush not only plays the role of sealing and blocking dust but also can clean the dust. Slide to the Side Garage Doors is a simple and flexible way to slide to the side of the garage and parallel to the wall. The bottom of the door is in close contact with the bottom surface, so it is recommended to install the garage door sealing brush strip on the top and both sides of the door. Side-Hinged Garage Doors is an old-fashioned garage door, which is similar to the doors we usually have at home. There are two symmetrical wooden doors. The working mode is push-pull. Generally, the garage door sealing brush strip can be installed on the upper and lower parts of the door. Yes, two gaps closed in the middle of the door can be installed if necessary. The working modes of Tilt-Up/Up and Over Canopy Garage Doors and Tilt-Up/Up and Over Retractable Garage Doors are not much different, but the installation positions are opposite. The former is installed facing outwards, while the latter is installed facing inwards. A garage door sealing brush strip is to be installed on the top, sides, and bottom of the door.
read more
If you want to know how the garage door seal brush strip works, you need to start with the structure of the garage door brush. The garage door seal brush strip is a kind of strip brush, which is composed of nylon wire, metal base, and fastening wire. Generally, it should be installed and used with aluminum strips of different angles. Tens of thousands of nylon filaments are regularly arranged on a plane. The tightly interlaced nylon filaments are connected together to block fine dust. There will be very small gaps between the filaments to allow air to circulate, ensuring air exchange. The garage door sealing brush has a good dust-proof effect and can ensure the circulation of air. This is the biggest advantage of the garage door sealing brush, and it has been used for many years. Each of AOQUN's garage door sealing brushes has passed the tensile test, and will not shed hair during use, and keep them neatly arranged and not easily deformed.
read more
Door sealing brushes strip have long been used by people to protect various doors. According to people's wisdom, many styles have been designed. Door sealing brushes are widely used on garage doors, domestic doors, revolving doors, traffic screen doors, and industrial doors. The door seal brush is versatile and can also be used flexibly. As a door seal brush manufacturer, we have summarized the following major uses, functions, and uses that customers will basically mention. The door seal brush mainly has the following functions: 1. Dustproof 2. Block Water, Mosquitoes, And Wind 3. Anti-Static 4. Flame Retardant And Fireproof 5. Heat And Cold Insulation, Noise Insulation 6. Power Saving, Safety, Sealing, Energy Saving, Polishing, Cleaning, Filtering The role of the door seal brush: 1. Prevent pests such as rodents from entering 2. Keeps out dirt, dust, and debris 3. Keep away from the wind, rain, snow, and other weather 4. Keep the indoor temperature under control 5. Provide privacy and security 6. Seal gaps between moving surfaces 7. Seal large gaps in commercial buildings The installation positions of the door seal brush are generally: the top of the door, both sides of the door, and the bottom of the door.
read more
The way a garage door works is very simple, up and down, left and right, open and closed again and again, year after year. Suddenly one day it doesn't work very well, there is a problem somewhere, maybe it takes simple maintenance and quick repairs to continue working. To inspect the corners of your garage door step-by-step: 1. With prolonged use, the rollers and tracks of the garage door are worn out, if you don't remember when it was last cleaned, use a good brush to clean the rollers and tracks now. Apply lubricant, or replace rollers that are not smooth. 2. To tighten the hardware. Various hardware screws can loosen due to the vibration of a bulky garage door as it slides, including the overhead brackets for the garage door, and the screws for the rails. Make sure that the screws in these parts are firm, and loosening the screws is a more dangerous thing. 3. The sealing brush of the garage door is a very important part to prevent insects from entering the garage, bite and destroy, and prevent dust from entering the garage. Therefore, it is necessary to check the garage door sealing brush at a certain time and replace it in time. 4. The long-term exposed side of the garage door has been eroded by rainwater and needs to be painted so that it will not be so easily oxidized and eroded. These are some of the problems I found in the maintenance of the garage door to pay attention to, I hope it can help you, and there are other garage door problems, I hope you can also come to communicate.
read more
Fast rolling shutter doors, also known as fast soft shutter doors, can always be seen in food, chemical, textile, electronics, supermarkets, refrigeration, logistics, warehousing, and other fields. It can maintain a clean environment for indoor places, such as combined with roller shutter door sealing strip brush, the effect is better. The roller shutter door sealing strip brush is used in combination with the aluminum alloy base and the sealing strip brush. Common aluminum alloy bases include h-type, F-type, Y-type, and T-type, and aluminum profiles of different specifications can be customized according to the use environment; sealing strip brushes are generally made of nylon, because nylon is soft, resilient, and durable. It is not deformed by grinding, and the sealing effect is good, which saves replacement costs for rolling shutter doors that are frequently opened and closed. Rolling shutter door installation sealing strip brush also has the functions of thermal insulation, heat insulation, sound insulation, dustproof, waterproof, insect and rat prevention, energy saving and environmental protection, it is indeed a "smart thing"! Aoqun Brush Factory can customize a variety of door seal brushes (such as garage doors, revolving doors, sliding doors, KFC doors, screen doors, etc.) The customer's door body needs to use drawings and samples, design and customize the aluminum alloy base sealing strip brush.
read more
Nowadays, many young people are particularly fond of custom-made furniture installation. When installing furniture, some detailed tutorials on solid wood installation steps still need to be very clear. For example, solid wood doors need to be installed at home. When installing solid wood doors, you need to Knowing the steps to install a custom solid wood door, let's follow the left and right editors to learn more about it! Installation conditions: 1. The conditions for the installation of customized solid wood doors must be the installation method of reserved holes, and it is forbidden to drill holes while installing. 2. If necessary, the installation can be carried out only after the installation of the groundworks at the entrance is completed. Material preparation: 1. Prepare the materials and appliances that need to be prepared to install the solid wood door to avoid omissions, such as hammers, screwdrivers, electric drills, etc., and check whether the parts are perfect and not damaged. 2. Check whether the size of each component is appropriate and whether the size of the door opening is consistent with the position where the door cover needs to be installed. 3. Prepare screws, styrofoam, glue, door sealing brush, and other tools. Detailed tutorial on installation steps of custom solid wood doors: 1. When installing the solid wood door, the first step is to place the components that need to be installed on the solid wood door on the gaskets laid in advance. 2. The next step is to assemble the door cover, use an electric hammer to make a hole at the door opening, and paste the anti-collision strip on the door cover. 3. Start to install the door frame, assemble the door frame with screws, and place it in the corresponding door opening after assembly. 4. Then start to install the door leaf. When installing the door leaf, it needs to be vertical, and at the same time, keep the corresponding distance from the door cover. 5. The next step is to install the door cover wire. When installing the door cover, you need to cut the door cover wire saw with a right-angled edge into an angle of 45 degrees, and you need to glue the door cover and the door cover line to each other. 6. The last part of the detailed tutorial on the installation steps of custom solid wood doors is to install the door lock, install the door lock according to the corresponding topic, check whether the switch is flexible after the installation of the door lock is completed, and also install the door bottom sealing brush, and this is done.
read more
scan to wechat
scan to wechat
